MCXA153 FRDM Board Test CDC+MSC A request for the USB device descriptor failed!!!!

[vscodeenv]

Operating System

Windows 10

Board

MCXA153 FRDM

Firmware

What happened ?

How to reproduce ?

all code from tinyusb V0.18 mcxa153 use FIRC clock！

Debug Log as txt file (LOG/CFG_TUSB_DEBUG=2)

USBD init on controller 0, speed = Full
sizeof(usbd_device_t) = 84
sizeof(dcd_event_t) = 12
sizeof(tu_fifo_t) = 20
sizeof(tu_edpt_stream_t) = 108
CDC init
MSC init
USBD Bus Reset : Full Speed

USBD Bus Reset : Full Speed

USBD Setup Received 80 06 00 01 00 00 40 00
Get Descriptor Device
Queue EP 80 with 18 bytes ...
USBD Xfer Complete on EP 80 with 18 bytes
Queue EP 00 with 0 bytes ...
USBD Xfer Complete on EP 00 with 0 bytes
USBD Bus Reset : Full Speed

USBD Setup Received 00 05 35 00 00 00 00 00
Set Address
USBD Xfer Complete on EP 80 with 0 bytes

USBD Setup Received 80 06 00 01 00 00 12 00
Get Descriptor Device
Queue EP 80 with 18 bytes ...
USBD Xfer Complete on EP 80 with 18 bytes
Queue EP 00 with 0 bytes ...
USBD Xfer Complete on EP 00 with 0 bytes

USBD Setup Received 80 06 00 02 00 00 FF 00
Get Descriptor Configuration[0]
Queue EP 80 with 64 bytes ...
USBD Xfer Complete on EP 80 with 64 bytes
Queue EP 80 with 34 bytes ...
USBD Xfer Complete on EP 80 with 34 bytes
Queue EP 00 with 0 bytes ...
USBD Xfer Complete on EP 00 with 0 bytes

USBD Setup Received 80 06 03 03 09 04 FF 00
Get Descriptor String[3]
Queue EP 80 with 34 bytes ...
USBD Xfer Complete on EP 80 with 34 bytes
Queue EP 00 with 0 bytes ...
USBD Xfer Complete on EP 00 with 0 bytes

USBD Setup Received 80 06 00 03 00 00 FF 00
Get Descriptor String[0]
Queue EP 80 with 4 bytes ...
USBD Xfer Complete on EP 80 with 4 bytes
Queue EP 00 with 0 bytes ...
USBD Xfer Complete on EP 00 with 0 bytes

USBD Setup Received 80 06 02 03 09 04 FF 00
Get Descriptor String[2]
Queue EP 80 with 30 bytes ...
USBD Xfer Complete on EP 80 with 30 bytes
Queue EP 00 with 0 bytes ...
USBD Xfer Complete on EP 00 with 0 bytes

USBD Setup Received 80 06 00 06 00 00 0A 00
Get Descriptor Device Qualifier
Stall EP0

USBD Setup Received 80 06 00 01 00 00 12 00
Get Descriptor Device
Queue EP 80 with 18 bytes ...
USBD Xfer Complete on EP 80 with 18 bytes
Queue EP 00 with 0 bytes ...
USBD Xfer Complete on EP 00 with 0 bytes

USBD Setup Received 80 06 00 02 00 00 09 00
Get Descriptor Configuration[0]
Queue EP 80 with 9 bytes ...
USBD Xfer Complete on EP 80 with 9 bytes
Queue EP 00 with 0 bytes ...
USBD Xfer Complete on EP 00 with 0 bytes

USBD Setup Received 80 06 00 02 00 00 62 00
Get Descriptor Configuration[0]
Queue EP 80 with 64 bytes ...
USBD Xfer Complete on EP 80 with 64 bytes
Queue EP 80 with 34 bytes ...
USBD Xfer Complete on EP 80 with 34 bytes
Queue EP 00 with 0 bytes ...
USBD Xfer Complete on EP 00 with 0 bytes

USBD Setup Received 00 09 01 00 00 00 00 00
Set Configuration
Open EP 81 with Size = 8
Open EP 02 with Size = 64
Open EP 82 with Size = 64
Queue EP 02 with 64 bytes ...
CDC opened

Screenshots

No response

I have checked existing issues, dicussion and documentation

• I confirm I have checked existing issues, dicussion and documentation.

[vscodeenv]

The computer heard the usb insert prompt sound, after about a few seconds to hear the usb sound again, and finally the program into the hardware error interrupted

[vscodeenv]

code run to TU_ASSERT(DRVID_INVALID == _usbd_dev.itf2drv[itf_num]); then hardfalt; can not run to _usbd_dev.itf2drv[itf_num] = drv_id; this is use GCC ; but use IAR has not this problem from same code

[vscodeenv]

my error